We had very little breeze in the morning so we were able to complete the stainless steel testing. The results for the forward port support were also encouraging. Having tested the key areas we now need to run the pictures by a metallurgist for their expert opinion.<\/p>\n

I managed to find someone in the yard who had an AIS receiver and was able to test the system. We first tested with the AIS splitter in place and didn’t see anything. I hindsight this might have been due to us not waiting long enough so this will need to be retested. After leaving the other boats AIS receiver on, going back to our boat, connecting the AIS transceiver directly to the antenna and returning to the other boat I could see Dignity loud and clear. I also managed to confirm that the boat length was indeed programmed incorrectly. In the end this turned out to be very easy to fix. While the configuration software stated it could not be reprogrammed twice, the message was referring only to the MMSID (radio license id). I can change the dimensions and ships name as much as I like.<\/p>\n

It’s worth noting that I’m definitely getting better range\/reception out of this new set up. I can see boats at the mouth of the river which we never could with our old antenna.<\/p>\n

The rest of the day was spent finishing off the nav station. It took more time than I had imagined but I got there in the end. You can see the before and after pictures in the slideshow at the end of this blog.<\/p>\n

Although it looks finished there are still a few things left to do. The SSB control head and speaker are loose and probably need to be glued on. In the past panel the speaker was jammed in but the current hole is just the right size so I can’t do that. Because the control head is nearer the edge I can’t use the old method I used to fix it. Hence I may have to glue them on. I also have to create a hole to run the USB cable from the SSB modem. I’ll also pass the wires for our portable GPS through this hole as will pass the RS232 connector that will allow my PC to receive information from the various GPSs. I then need to connect all this up via the rotary selector switch and connect these all to the SSB and VHF radio so each unit will receive GPS signals again. In doing all this I also need to connect the new AIS to the chart plotter.<\/p>\n

Ok. So I haven’t finished the nav station but it looks it and I feel happy with the result.<\/p>\n

Bertrand and Joel came for the morning. They spent quite a lot of time on the rear rail which covers the join between the top half of the boat and the bottom. Turns out the weight of the dinghy and the movement at sea have pulled the parts apart. They fixed all this and did a fantastic job of it. The pics below show the separated parts (after all the current glue had been removed). Need to get one of the finished result as it looks good. I need to hunt around for what else they did. It’s hard to keep track at times.<\/p>\n

<\/embed><\/p>\n

In the evening there was a bit of a get together at the communal area to hear about some recent adventures of a mixture of Fijians and westerners who took to the sea in a group of vessels based upon traditional Fijian designs. It was quite interesting but a great excuse to get everyone together. Dave and Suzie from Sidewinder were there as were Derek and Alison from Kalida. We met a few other folks from here in the yard who we hope to see again over time.<\/p>\n","protected":false},"excerpt":{"rendered":"

We had very little breeze in the morning so we were able to complete the stainless steel testing. The results for the forward port support were also encouraging. Having tested the key areas we now need to run the pictures by a metallurgist for their expert opinion.<\/p>\n

I managed to find someone in the yard […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[199,130,138],"tags":[],"class_list":["post-5416","post","type-post","status-publish","format-standard","hentry","category-kalida","category-new-zealand","category-sidewinder","odd"],"_links":{"self":[{"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/posts\/5416","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=5416"}],"version-history":[{"count":6,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/posts\/5416\/revisions"}],"predecessor-version":[{"id":5423,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=\/wp\/v2\/posts\/5416\/revisions\/5423"}],"wp:attachment":[{"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=5416"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=5416"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/aboarddignity.com\/blog\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=5416"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}